YASKAWA Japan Electric 0.45KW servo driver 3Phase Input 5.0 AMPS SGDB-05ADG

SGDB-20ADG

SGDB-20ADM

SGDB-20ADP

SGDB-20ADS

SGDB-20ADS /G/M+SGMS-20ACA2C/SGMS-20ACA21

SGDB-20ADS G

SGDB-20ADS M

SGDB-20ADS M+SGMS-20ACA21

SGDB-20AN

SGDB-20VD

SGDB-20VN

SGDB-30AD

SGDB-30ADG

SGDB-30ADG-P

SGDB-30ADM

SGDB-30AN

SGDB-30AN-P

SGDB-44AD

SGDB-44ADG

SGDB-44ADGY181

SGDB-44ADGY8

SGDB-44ADM

SGDB-44ADS

SGDB-50ADS

SGDB-50ADTY283

SGDB-50ADTY283+SGMT-40A2A-NV13

SGDB-60AD

SGDB-60ADB

SGDB-60ADG

SGDB-60ADM

SGDB-60DV

SGDB-60VD

SGDB-75AD
.

Open Chassis Type (IEC IP00)Protected so that parts of the human body cannot reach electrically charged parts from the front when theDrive is mounted in a control panel, also called (protected chassis).TERMSNEMA 1 Type (IEC IP20)The Drive is shielded from the exterior, and can thus be mounted to the interior wall of a standard building(not necessarily enclosed in a control panel). The protective structure conforms to the standards of NEMA 1in the USA. Top protective cover (Fig 1.4) must be installed to conform with IEC IP20 and NEMA Type 1requirements.

Please perform the following tasks after receiving the PROFIBUS-DP Option:• Inspect the PROFIBUS-DP Option for damage.If the PROFIBUS-DP Option appears damaged upon receipt, contact the shipper immediately.• Verify receipt of the correct model by checking the information on the nameplate (see• If you receive the wrong model or the PROFIBUS-DP Option does not function properly, contact your supplier.

4 PROFIBUS-DP Option ComponentsuCommunication connectorThe drive has a 9 pin D-sub connector for installing the option card. Once installed, the drive can connect to aPROFIBUS network.Figure 4PROFIBUS ConnectorBottom View162738495uPROFIBUS-DP Option LED DisplayDisplayLEDColorRUNGreen(Power)ERRRed(Option Error)COMM(CommunicationGreenStatus)BF(PROFIBUS-DPRedError)10Figure 4 Communication connector locationTable 3 Communication connector (9-pin D-SUB)PinSignal1Shield2–3RxD/TxD-P4CNTR-P5DGND6VP7–8RxD/TxD-N9–Table 4 LED DisplayCommunicationStatusStatusONPower is onOFFPower is offONSI-P3/V errorFlashingDrive connection errorOFFNormal operationCommunicationONconnectedOFFNo data exchangeWaiting forONcommunicationprocedure settingCommunication settingFlashingerrorOFFNormal operationConnected to the metal-shell (no direct FG-connection)Receive/Transmit data; line B (red)Control signal for repeaters (direction control)Data ground (reference voltage to VP)Power supply output for bus termination (for termination resistor)Receive/Transmit data; line A (green)Power is being properly supplied to SI-P3/V, and SI-P3/V has completed itshardware self-diagnostics check• The drive has no power supply• SI-P3/V and drive are not connected properly and/or there is no powersupplied to the SI-P3/V• An internal, self-diagnostic error occurred in the SI-P3/VSelf-diagnostics error occurred in the SI-P3/VConnection error between SI-P3/V and drive. This includes node addresssetting errors to parameter F6-30 on the drive sideDrive and SI-P3/V are properly connectedNormal send/receive between SI-P3/V and PROFIBUS-DP masterThere is a problem establishing communication between SI-P3/V and thePROFIBUS-DP masterCommunication-related parameters are being set or initialized by thePROFIBUS-DP master.Communication parameter error from PROFIBUS-DP masterLED is off once the PROFIBUS-DP master is finished settingcommunication-related parameters

OTHER SUPERIOR PRODUCTS